Japan PSE certification

 一、Japan PSE certification introduction

All products that belong to the catalog in the Japanese PSE certification must obtain product certificate and affix the Japan PSE certification mark on the product to enter the Japanese market.

Japan round PSE certification products have more categories. The round PSE certification requirements are simpler than the Japan diamond PSE certification. The Japan diamond-shaped PSE certification is more complicated and requires factory inspections.

PSE certification is a compulsory safety certification in Japan. It is used to prove that electrical and electronic products have passed the safety standards test of the Japanese Electrical and Material Safety Law (DENAN Law) or international IEC standards. Japan's DENTORL Act (Electrical Device and Material Control Act) stipulates that 506 products must pass safety certification to enter the Japanese market. Among them, 165 types of A products should obtain the diamond-shaped PSE mark, and 341 types of B products should obtain the circular PSE mark.


Post image


Post image

二、Applicable product range

Diamond PSE

Electric wires, wiring appliances, current limiters, transformers, stabilizers, electric heating appliances, electric power application machinery, AC electrical machinery, portable generators, other AC machinery, electrical conduits, small AC motors, light sources and light sources Applied machinery, batteries, etc. belong to the product range specified by the Safety Law for Certain Electrical Supplies, such as: DC power supply devices, switches and sockets, electric water heaters, power cords and plugs, other household appliance transformers (AC-AC power products), etc. 165 products.

Round PSE

Products that fall outside the specific electrical appliance safety law, such as: electric blankets, electric steamers, electric irons, electric ovens, microwave ovens, hair humidifiers, refrigerators, electric mixers, electric egg cookers, and electric insulation basins , Hair dryer, electric humidifier, projector, washing machine, incandescent bulb, fluorescent lamp, table lamp, decorative lamp, advertising lamp, lithium battery and all 341 products such as LED bulbs and LED lamps.

This is the introduction of PSE certification in Japan. Deeplight Technology is familiar with several Japanese Compulsory Certifications of electronic products,such as Japan radio law Telec certification (applicable for wireless products), Japan telecommunication law JATE certification (telecommunication products) and so on.Welcome to contact us about Japan certification.

Email: jl@dlcer.comWeChat:dlcert        Mobile:+86-18038042309     Tel:+86-755-8920 2795

Comments

Post a Comment

Popular posts from this blog

Deeplight Technology Bluetooth protocol BQB certification services

Image
  Bluetooth BQB certification is a routine projects now. Most of Bluetooth BQB certification are end product certification. For many end product BQB certifications, only the lowest layer RF testing +top layer application profiles testing are required, which is easy to testing. So, who will test the Buetooth protocol stack layer? Generally,Bluetooth chip companies\Bluetooth solution companies\Bluetooth protocol stack software development companies need testing Buetooth protocol stack layer. Deeplight Technology has a case which Bluetooth product need testing profile and RF to protocol. At present, the Deeplight Technology has begun to carry out the Bluetooth protocol stack BQB certification testing, which includes all the protocol layer testing such as BLE 2M rate\coded\stable modulation index\AoA\AoD\BLE audio… The Bluetooth BQB certification testing has the following layers according to the Bluetooth SIG: (1) The lowest Bluetooth physical layer:RF, RF-PHY. (2) Intermediate protocol st
Read more

Deeplight Tech Laser Products NRTL\IEC60825-1\FDA Standards 21 CFR 1040.10 testing and certification services

Image
  In the sales process of laser products, whether it is normal offline sales or online sales, safety issues will be involved.   Most testing of laser safety issues is defined by IEC standards. IEC 60825-1:2014 is laser product s  safety   testing standard, Part 1  is Equipment classification and requirements.     The D eeplight Tech can not only complete the IEC 60825-1:2014 standard test of laser products, but also complete the FDA standard 21 CFR 1040.10 test ing , u ntil obtaining FDA completed email and FDA listing for customers.   In the same way, laser products are sold in the U.S. market, and D eeplight Tech  can also help customers complete NRTL certification of laser products , one-stop completion.       The NRTL\IEC60825-1\FDA Standard   21 CFR 1040.10 laser products test ing  content briefly introduced:   1.CLASSIFICATION PRINCIPLES (1) Radiation of a single wavelength , Wavelength : λ: 532nm. (2) Radiation of multiple wavelengths , Laser product emits at two or more wavelen
Read more

Deeplight Technology OTA testing service of wireless products

Image
  1.There are two methods to test the radiation performance of wireless product. (1)PASSIVE test: Test the product antenna's radiation performance,passive testing focuses on product antenna's radiation performance from the antenna's gain, efficiency, pattern and other antenna radiation parameters. Commonly used test cases are: Return Loss; Directivity; Gain, dBi or dBd. Efficiency; Radiation Pattern (direction diagram). Effective Isotropic Radiated Power (Gain + Transmit Power). Input Impedance (antenna interface impedance test). VSWR, RL (antenna standing wave ratio, return loss test); 3D (3D field strength map). 3dB BW, FB Ratio (beam width, front-to-back ratio). Cross polar, Isolation (cross polarization ratio, isolation). Directivity; Efficiency. (2)ACTIVE test: In the microwave anechoic chamber,testing of the radiated power and receiving sensitivity of the product,namely TRP and TIS. This method can better reflect the overall radiation performance of the product Wirele
Read more